Picture

RG-N18010-XH – Next Generation Data Center Network High-Density Centralized Modular Core Switch with 100GE/400GE Line Cards and Eight Service Slots

Adaptation to 400GE ZR/ZR+ optical modules, up to 288 x 400GE and 1152 x 100GE line-rate ports, and smooth evolution to 800GE

Models

RG-N18010-XH

8 Service Slots, 100GE/400GE Line Cards

Series

RG-N18000-XH Series

Datasheet Sales Enquiry

Highlight Features

100GE and 400GE line cards, and up to 288 x 400GE and 1152 x 100GE line-rate ports
Communication at the maximum distance of 120 km and easy DCI
Hardware-level redundancy, ensuring nonstop services and data center network stability
MACsec data encryption and transmission, effectively protecting service data security
Innovative technology design and efficient heat dissipation, with more than 50,000 kWh saved per device each year
Telemetry-based network monitoring and automated O&M, making management simple and efficient...

Key Specification
Features
Specifications
Resources
Order Information

Sales Enquiry

Key Specification View More

Features

Data Center 400GE Modular
Core Switch
RG-N18010-XH

The RG-N18010-XH provides 10 module
slots, including eight service slots, which can
be used with 100GE and 400GE line cards. It
supports 800GE line cards in the future,
easily coping with future bandwidth
expansion needs.
With various port types, the RG-N18010-XH
supports up to 288 x 400GE and 1152 x
100GE line-rate ports, and allows smooth
evolution to 800GE, satisfying requirements
in diversified scenarios of data center
networks.

Innovative Architecture Design,
Achieving Highly Efficient Data Transmission

Zero Midplane

Clos Architecture

Service line cards are directly connected to SFUs, without the use of the midplane. Data can directly reach the SFU, with a
short distance. This significantly reduces the transmission loss and achieves efficient data transmission.

Communication at the Maximum Distance of 120 KM and Easy DCI

400GE ZR/ZR+ optical modules are used for interconnection, reducing Optical Transport Units (OTUs) and helping a cloud or hyper-scale
data center network to adapt to growing high-bandwidth services

Hardware-level Redundancy,
Ensuring Nonstop Services and Data
Center Network Stability

SFUs in N+1 Redundancy Mode

SFUs use N+1 redundancy and work in load balancing
mode, ensuring nonstop services.

Power Modules in M+N Redundancy Mode

Ten hot-swappable power modules are available. When a
fault occurs, services are switched within seconds. Services
are not interrupted when a power module is replaced. The
switch provides different protection measures for links.

Fan Trays in 2+1 Redundancy Mode

Three hot-swappable fan trays are available. The speed of
fan modules can be intelligently adjusted, ensuring highly
efficient heat dissipation.

Supervisor Engin es in 1+1 Redundancy Mode

The 1+1 hot standby design ensure continuous operation of
the switch.

Innovative Technology Design and Highly Efficient Heat Dissipation

MACsec Data Encryption and Transmission,
Effectively Protecting Service Data Security

MACsec provides hardware-level data encryption. With MACsec and 802.1X configured, the switch can strictly identify and verify transmitted data.
With MACsec, the switch achieves interface-based secure line-rate transmission, effectively preventing data from being intercepted and obtained maliciously
and ensuring service data security.

Telemetry-based Network Monitoring and Automated O&M,
Making Management Simple and Efficient

The switch enabled with telemetry provides clear data status and hierarchy.
The switch uses the push mode to proactively collect and push information and to provide sub-second-level network monitoring in real time,
making network management more efficient and accurate.

Specifications

Hardware Specifications

Item	RG-N18018-XH	RG-N18010-XH
Dimensions (W x D x H)	442 mm x 1052 mm x 1345 mm (17.40 in. x 41.42 in. x 52.95 in.), without the cable management bracket; 442 mm x 1091 mm x 1345 mm (17.40 in. x 42.95 in. x 52.95 in.), with the cable management bracket.	442 mm x 896 mm x 708 mm (17.40 in. X 35.28 in. X 27.87 in.), without the cable management bracket; 442 mm x 935 mm x 708 mm (17.40 in. x 36.81 in. X 27.87 in.), with the cable management bracket.
Rack height	31 RU	16 RU
Unit weight	205 kg (451.95 lbs.), with M18018XH-FAN fan modules; 186 kg (410.06 lbs.), with M18018XH-FAN III fan modules.	96.4 kg (212.53 lbs.) (Chassis that supports the M18000XH-CM supervisor module) 99 kg (218.26 lbs.) (Chassis that supports the M18000XH-CM II supervisor module)
Switching capacity	1,290 Tbps/3,870 Tbps	645 Tbps/1,935 Tbps
Packet forwarding rate	691,200 Mpps	345,600 Mpps
Module slot	2 x supervisor module slots 16 x line card slots 8 x switch fabric module slots 20 x power module slots 3 x fan module slots	2 x supervisor module slots 8 x line card slots 8 x switch fabric module slots 10 x power module slots 3 x fan module slots
Power consumption	Maximum power consumption (with the M18018XH-FAN fan module): 38,900 W Maximum power consumption (with the M18018XH-FAN III fan module): 18,000 W	Maximum power consumption (with the M18010XH-FAN fan module): 187,600 W Maximum power consumption (with the M18010XH-FAN III fan module): 9000 W
Power input	RG-PAH3000I-F (AC input): Rated input voltage: 100 V AC to 130 V AC, 200 V AC to 240 V AC, 50 Hz/60 Hz Maximum input voltage: 90 V AC to 290 V AC, 45 Hz to 65 Hz Rated input current: 16 A Power port type: C20 RG-PAH3000I-F (HVDC input): Rated input voltage: 240 V DC to 380 V DC Maximum input voltage: 188 V DC to 400 V DC Rated input current: 14 A Power port type: C20 Note: When the switch is equipped with the high-voltage DC power supply, a PDU that supports high-voltage DC power supply must be used. To ensure safety, connect the external power supply to the power cord first and then to the PDU. The switch can only connect to a specific power system (UPS) but not to the DC power grid. The DC voltage tolerance range is from 188 V DC to 400 V DC. PD2200II-F (DC input): Rated input voltage: –48 V DC to –60 V DC Maximum input voltage: –38 V DC to –72 V DC Rated input current: 50 A Power port type: Rectangular non-metallic locking plug	RG-PAH3000I-F (AC input): Rated input voltage: 100 V to 130 VAC, 200 V AC to 240 V AC, 50 Hz/60 Hz Maximum input voltage: 90 V AC to 290 V AC, 45 Hz to 65 Hz Rated input current: 16 A Power port type: C20 RG-PAH3000I-F (HVDC input): Rated input voltage: 240 V DC to 380 V DC Maximum input voltage: 188 V DC to 400 V DC Rated input current: 14 A Power port type: C20 Note: When the switch is equipped with the high-voltage DC power supply, a PDU that supports high-voltage DC power supply must be used. To ensure safety, connect the external power supply to the power cord first and then to the PDU. The switch can only connect to a specific power system (UPS) but not to the DC power grid. The DC voltage tolerance range is from 188 V DC to 400 V DC. PD2200II-F (DC input): Rated input voltage: –48 V DC to –60 V DC Maximum input voltage: –38 V DC to –72 V DC Rated input current: 50 A Power port type: Rectangular non-metallic locking plug
Temperature	Operating temperature: 0°C to 40°C (32°F to 104°F) Storage temperature: –40°C to +70°C (–40°F to +158°F) Note: At altitudes ranging from 1800 m (5,905.51 ft.) to 5000 m (16,404.20 ft.), the maximum temperature decreases by 1°C (1.8°F) for every 200 m (656.17 ft.) increase in elevation.
Humidity	Operating humidity: 10% RH to 90% RH (non-condensing)
Altitude	Operating altitude: ≤ 5,000 m (16,404.20 ft.) Storage altitude: ≤ 5000 m (16,404.20 ft.)
Cooling	Air cooling, front-to-rear airflow (port-side air intake)

Software Specifications

Item	RG-N18018-XH	RG-N18010-XH
Traffic analysis	sFlow IPFIX
Layer 2 features	Jumbo frame IEEE 802.3ad (static link aggregation, LACP, cross-module link aggregation, and M-LAG) IEEE 802.1Q STP, RSTP, and MSTP GVRP QinQ LLDP Static MAC addresses, address filtering, and limit on the number of MAC addresses
IPv4 features	Static routing, BGP4, OSPF, IS-IS, and RIP VRRP ECMP Policy-based routing IP fragmentation and reassembly Manual tunnel and GRE tunnel
IPv6 features	Static routing, BGP4+, OSPFv3, IS-ISv6, and RIPng VRRPv3 ECMP Policy-based routing Path MTU discovery IP fragmentation and reassembly Manual tunnel and GRE tunnel Pingv6, Traceroutev6, Telnetv6, FTPv6, TFTPv6, DNSv6, and ICMPv6
Multicast	IGMP v1/v2/v3 IGMP Snooping v1/v2 IGMP proxy PIM-DM, PIM-SM, PIM-SSM, and PIM-SM v6 MLDv1, MLDv2 Static multi cast route Fast leave
MPLS	MPLS L3VPN MPLS LDP SR MPLS (Segment Routing) SR-TE
ACL	Standard, extended (Layer 2 to layer 4), and expert ACL Global ACL Ingress and egress ACL IPv6 ACL
QoS	IEEE 802.1p, ToS, and DSCP priority mapping Priority marking and remarking SP(PQ), DRR, SP(PQ)+DRR, WFQ, SP(PQ)+WFQ, and other queue scheduling mechanisms Congestion avoidance mechanisms such as RED and WRED ACL Egress/ingress port-based rate limit and CAR #MPLS QoS
Data center features	#SRv6 VXLAN bridge VXLAN gateway BGP-EVPN VXLAN VXLAN mapping VXLAN over IPv4 VXLAN over IPv6 M-LAG RDMA
SDN	OpenFlow 1.3
Reliability	Independent switch fabric modules and independent supervisor modules to implement thorough separation of the forwarding plane from the control plane 1+1 redundancy for supervisor modules N+M redundancy for switch fabric modules N+M redundancy for power modules and fan modules Midplane-free design to avoid single point of failures Hot swapping of components Hot patching for online patch upgrade BPDU Guard/Loop Guard/Root guard NSR DLDP FRR GR for OSPF/IS-IS/BGP BFD for VRRP/OSPF/BGP4/ISIS/ISISv6/Static routing
Virtualization	Virtual switching unit (VSU)
Security	#MACSec Network foundation protection protocol (NFPP) and CPU Protection Policy (CPP) DDoS attack defense, ARP attack defense, and ICMP attack defense DAI, port security, IP source guard, and port protection uRPF RADIUS and TACACS authentication, password security, hierarchical user management, and password protection Source IP address restriction Configuring the device not to send unknown multicast packets to the CPU Suppression of unknown unicast, broadcast, and multicast packets SSHv2, providing secure encrypted channels for user login MAC address flapping protection policy Clear text and MD5 authentication for BGP4, BGP4+, OSPF, OSPFv3, IS-IS, IS-ISv6, and RIPv2 packets
Management	Console/AUX Modem/Telnet/SSHv2 CLI configuration FTP, TFTP, Xmodem, and SFTP SNMP v1/v2c/v3 Netconf RMON NTP clock Fault alarm and auto-recovery System operation log Traffic analysis Zero-Touch provisioning (ZTP) Reliable network service (RNS), which probes specific services provided by the peer device to monitor the service availability Telemetry Buffer status monitoring and traffic microburst identification Supported VXLAN OAM: VXLAN ping VXLAN tracert Port mirroring, traffic mirroring, and ERSPAN Physical ports on all line cards support routing mode and can be configured with IP addresses independently Fan and power module monitoring

# indicates that the feature is supported only by CE line cards.

Resources All Resources

Learn about Products or Solutions

Product Datasheet

Installation

Installation Guide

Order Information

Chassis and Supervisor Modules

Model	Description
RG-N18018-XH	RG- N18018-XH switch, fully equipped with fan modules, without power modules
RG-N18010-XH	RG-N18010-XH chassis, fully equipped with fan modules, without power modules
M18000XH-CM	M18000XH-CM supervisor module, used with Type E switch fabric modules and CE line cards
M18000XH-CM II	M18000XH-CM II supervisor module, used with Type D switch fabric modules and DB line cards

Power Module

Model	Description
RG-PAH3000I-F	3000 W AC power module (supporting AC and 240 V to 380 V HVDC)
PD2200II-F	2200 W DC power module (supporting 54 V DC), applicable to RG-N18018-XH and RG-N18010-XH

Switch Fabric Module

Model	Description
M18018XH-FE-E IV	Type E series switch fabric module of RG-N18018-XH, used with CE line cards
M18018XH-FE-D II	Type D switch fabric module of RG-N18018-XH, used with DB line cards
M18010XH-FE-E II	Type E series switch fabric module of RG-N18010-XH, used with CE line cards
M18010XH-FE-D II	Type D switch fabric module of RG-N18010-XH, used with DB line cards
M18006XH-FE-D I	Type D switch fabric module of RG-N18006-XH, used with DB line cards

Line Cards and Function Modules

Model	Description
M18000XH-36QC-CES	36-port 400G (QSFP-DD) Ethernet optical interface card, CE line card, used together with Type E switch fabric modules
M18000XH-48CQ-CES	48-port 100G QSFP28 Ethernet optical interface card, CE line card, used with Type E series switch fabric modules
M18000XH-36CQ-DB	36-port 100G QSFP28 Ethernet optical interface card, DB line card, used with Type D switch fabric modules
M18000XH-18CQ-DB	18-port 100G QSFP28 Ethernet optical interface card, DB line card, used with Type D switch fabric modules
M18000XH-36QXS-DB	36-port 40G QSFP+ Ethernet optical interface card, DB line card, used with Type D switch fabric modules
M18000XH-48XS-DB	48-port 10G SFP+ Ethernet optical interface card, DB line card, used with Type D switch fabric modules

25G Optical Transceivers

Model	Description
VG-SFP-AOC5M	25G active optical cable (AOC), SFP28 form factor, 5 m (16.40 ft.)
VG-SFP-SR-SM850	25G SR optical transceiver, SFP28 form factor, LC interface, 850 nm, 100 m (328.08 ft.) over multimode fiber (MMF)
VG-SFP-LR-SM1310	25G LR4 optical transceiver, SFP28 form factor, LC interface, 1310 nm, 10 km (32,808.40 ft.) over single-mode fiber (SMF)

40G Optical Transceivers

Model	Description
40G-QSFP-LX4-SM1310	40G LX4 optical transceiver, QSFP+ form factor, Duplex LC, 150 m (492.13 ft.) over OM3/OM4 MMF, or 2 km (6,561.68 ft.) over SMF
40G-QSFP-LR4-SM1310	40G LR4 optical transceiver, QSFP+ form factor, Duplex LC, 10 km (32,808.40 ft.) over SMF
40G-QSFP-iLR4-SM1310	40G iLR4 optical transceiver, QSFP+ form factor, Duplex LC, 2 km (6,561.68 ft.) over SMF
40G-QSFP-LSR-MM850	40G SR optical transceiver, QSFP+ form factor, MPO interface, 400 m (1,312.34 ft.) over MMF
40G-QSFP-SR-MM850	40G SR optical transceiver, QSFP+ form factor, MPO interface, 150 m (492.13 ft.) over MMF
40G-AOC-30M	40G QSFP+ AOC, 30 m (98.43 ft.)
40G-AOC-5M	40G QSFP+ AOC, 5 m (16.40 ft.)

100G Optical Transceivers

Model	Description
100G-QSFP-LR4-SM1310	100G LR4 optical transceiver, QSFP28 form factor, Duplex LC, 1310 nm, 10 km (32,808.40 ft.) over SMF
100G-QSFP-iLR4-SM1310	100G iLR4 optical transceiver, QSFP28 form factor, Duplex LC, 1310 nm, 2 km (6,561.68 ft.) over SMF
100G-QSFP-ER4-SM1310	100G ER4 optical transceiver, QSFP28 form factor, Duplex LC, 1310 nm, 40 km (131,233.60 ft.) over SMF
100G-QSFP-SR-MM850	100GSR optical transceiver, QSFP28 form factor, MPO interface, 850 nm, 100 m (328.08 ft.) over MMF
100G-AOC-5M	100G AOC, QSFP28 form factor, 5 m (16.40 ft.)
100G-AOC-10M	100G AOC, QSFP28 form factor, 10 m (32.81 ft.)

400G Optical Transceivers

Model	Description
400G-QDD-DR4-SM1310	400G optical transceiver, QSFP-DD form factor, MPO-12 APC, 1310 nm, 500 m (1,640.42 ft.) over SMF
400G-QDD-FR4-SM1310	400G FR4 optical transceiver, QSFP-DD form factor, Duplex LC, 1310 nm, 2 km (6,561.68 ft.) over SMF
400G-QDD-ZR-SM1550	400G ZR optical transceiver, QSFP-DD form factor, Duplex LC, 1550 nm, 80 km (262,467.19 ft.) over SMF
400G-QDD-SR8-MM850	400G optical transceiver, QSFP-DD form factor, MPO-16 APC, 850 nm, 100 m (328.08 ft.) over MMF

5-Star Hotel Solution

RG-N18010-XH – Next Generation Data Center Network High-Density Centralized Modular Core Switch with 100GE/400GE Line Cards and Eight Service Slots

100GE and 400GE line cards, and up to 288 x 400GE and 1152 x 100GE line-rate ports

Communication at the maximum distance of 120 km and easy DCI

Hardware-level redundancy, ensuring nonstop services and data center network stability

MACsec data encryption and transmission, effectively protecting service data security

Innovative technology design and efficient heat dissipation, with more than 50,000 kWh saved per device each year

Telemetry-based network monitoring and automated O&M, making management simple and efficient...

Data Center 400GE Modular Core SwitchRG-N18010-XH

Innovative Architecture Design,Achieving Highly Efficient Data Transmission

Zero Midplane

Clos Architecture

Communication at the Maximum Distance of 120 KM and Easy DCI

400GE ZR/ZR+ optical modules are used for interconnection, reducing Optical Transport Units (OTUs) and helping a cloud or hyper-scale data center network to adapt to growing high-bandwidth services

Hardware-level Redundancy,Ensuring Nonstop Services and Data Center Network Stability